Dynam C-310 Grand Cruiser V2 Specification
Wingspan: 1280mm/(50.39"Overall Length: 1100mm/43.3in"
Flying Weight: 1200g/42.32oz
Wing Loading: 58g/dm²
Motor: 2x Detrum BM2815-1100KV (CW & CCW) brushless outrunner
ESC: 2x Skylord-40A 5A-BEC
Prop: 2x 3-blade prop 8*6*3 (CW & CCW)
Servo: 4x 9g micro servos
Landing Gear: E-Retract (Retractable)
Tx: 6CH+ 2.4Ghz 6-Channel or above
Rx: 6CH 2.4Ghz
Battery: 3S 11.1V 2200mAh Li-Po 25C
Aileron: Yes
Elevator: Yes
Rudder: Yes
Flaps: Yes
Material: EPO Foam
C-310 Grand Cruiser V2 Spare Part List
|
grand-01 Fuselage |
grand-02 Wing |
grand-03 Vertical Stabilizer |
|
grand-04 Elevator |
grand-05 Wing Tip |
grand-06 Propeller |
|
BM2815A-KV1100 Motor |
grand-07 Plastic Part |
grand-08 Landing Gear |
|
grand-09 Blister |
grand-10 Spinner |
grand-11 Push Rod |
|
grand-12 Decal |
grand-13 Plastic Tab |
grand-14 Cowl |
|
grand-15 Screw Set |
DY-1007 9g Servo |
DY-1023 E-Retract φ3.1 90° |
|
DY-1024 Front E-Retract |
DY-6006 11.1V 2200mAh |
DTM-T006 Gavin-6C Tx |
|
DY-3003 Epoxy Glue |
Skylord-40A 5A-BEC |
DYR-2001 2.4G Rx |
|
DYAT-008 Servo Horn |
DY-3001 Quick-Controller |
DY-3007 Flap Hinges |
C-310 Grand Cruiser V2 Assembly
1. Insert the flat end of the vertical tail groove. |
2. Installed in the fuselage. |
|
3. Lock screws vertical tail and horizontal tail. |
4. The rudder rod penetration quick connector, tighten with a screwdriver. |
5. The elevator rod penetration quick connector is tightened with a screwdriver. |
6. Insert one end of the steering rod Z-map in the marked plastic parts. |
7. Fixed front wheel steering with PA2.5*6mm. |
8. Coated foam to fill in the blank block and the body fit. |
9. Front wheel into quick connector to the rod fastened with a screwdriver. |
10. Coated foam around the wing tip to the wing in the bonding. |
|
11. Icon to install clover by the propeller. |
12. As shown in the installation of the propeller fairing. |
|
13. After installing the landing gear by Icon. |
14. Aileron cable with Y-cable. |
|
15. The power transfer signal cable into the receiver channel THR. |
16. Fixed-wing screw with M3*35mm. |
|
17. Body antenna installation. |
18. Installing the battery position. |
C-310 Grand Cruiser V2 Decal
Directions for C-310 Grand Cruiser V2 Assembly & Adjustment
CENTER OF GRAVITY (C.G.)
The ideal C.G. position is 55~65mm behind the leading edge, measured where the wing meets the fuselage. Add weight to the fuselage or move the battery position to obtain the C.G. specified. Check the C.G. before flying.
